Parts & Accessories
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs with 126mm spacing - Type: Hollow Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 137mm - 1 axle per bag
$1.50 - $6.25
Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually
WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 34mm
WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 46mm
WTB's TCS Brass Valves are your key to the excellence that is tubeless wheels and tires. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch.
$15.00 - $79.95
Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).
- Replacement rear skewer - Spacing: 135mm - Material: Steel
- Supplies full wheel illumination for 700c/29in wheels and smaller - Approximately 40 hrs of battery life - Water resistant design - Includes 3 (AA) batteries - Sold individually (1 wheel) - Easy to install
$20.00 - $21.00
Front end cap conversion kits for NoTubes Neo and Neo Ultimate - SealLock end caps feature a low friction U-cup seal that snaps into place
$20.00 - $23.00
Rear end cap conversion kits for NoTubes Neo and Neo Ultimate hubs - SealLock end caps feature a low friction U-cup seal that snaps into place
$15.95 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
$17.99 - $19.95
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
Compatible with straight valve hole Hugo 52 rims and designed to fit 7.5 - 8.5mm valve holes. Sold as a pair. Identifying your Hugo rim and selecting the correct valve stem: Stepped Hugo rims have a larger diameter valve hole on the interior of the rim, and a narrower hole on outside of the rim. Quick tip: don't remove your tire if you don't have to. If your Hugo rim decal reads: MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this valve. For "Stepped" valve hole Hugo use part AS0105 - Valve Stem pair, Schrader, 32mm, 14mm base.
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
$20.00 - $24.99
Booster thru-axle hub spacer kits are designed to give your non-Boost front and rear thru-axle hubs the boost they need to fit any Boost-compatible frame or fork.
Origin-8's Pro Pulsion Rim Strips are made from a super-durable, environmentally friendly PVC material.
$15.29 - $26.69
- AL6061 alloy tubeless Presta valve - Includes 2 O-rings, one standard profile and one aero profile, for an airtight seal on any rim - Removable valve core for installing sealant - Additional replacement valve cores sold separately - Sold individually
- Longer skewers fit modern frames/forks with thicker dropouts - Aluminum lever/nut, Delrin pivot washer, serrated alloy nut with Nylock - White skewers are powder-coated - Shaft: chromoly - Wheel: front/rear - Spacing (front/rear): 100/135mm - Weight: 112g/set
$5.00 - $6.50
- Strong nylon reinforced PVC for a secure fit - Handles high-pressures; does not rot - 0.5mm thick
- Extra security against theft - 5mm hex CrMo axle
DT-Swiss Center Lock Adaptor. Allows 6-bolt rotors to be used on Center Lock hubs. - Rotor thickness between 1.8mm and 2.2mm - Easy assembly and only 29g - Made in Switzerland by DT Swiss - 230mm version accepts all rotors up to 203mm diameter - 160mm version accepts all rotors up to 160mm diameter
DT Swiss tubeless-ready tape seals the rim for tubeless applications and also works well as rim tape for tube-type setups. - Durable adhesive tape works as a rim tape and airseal
$8.39 - $10.00
- Plastic spoke covers in a variety of colors - 300mm cut to fit length - 36 pieces - enough for one wheel - Increases visibility and demands attention
This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum
$17.10 - $28.00
Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.
Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm. Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.
- Lowest resistance hybrid ceramic (ceramic balls and steel cages) available - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Kits include Freehub body with CeramicSpeed
$116.30 - $133.00
Freehub bodies for Zipp Cognition hubs.
Zipp Speed Weaponry Rear Axle Conversion Kits - Converts a road disc into a track disc rear - Fits black 2013 188 V8 disc hubs only - Fits Zipp 900 and Super-9 Discs
These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals. Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.
Page 1 of 13 Next page