Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs with 126mm spacing - Type: Hollow Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 137mm - 1 axle per bag
$1.25 - $5.75
Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually
WTB's TCS Brass Valves are your key to the excellence that is tubeless wheels and tires. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch.
$15.00 - $79.95
Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).
- Replacement rear skewer - Spacing: 135mm - Material: Steel
- Supplies full wheel illumination for 700c/29in wheels and smaller - Approximately 40 hrs of battery life - Water resistant design - Includes 3 (AA) batteries - Sold individually (1 wheel) - Easy to install
Converts a Stan's 3.30/3.30Ti rear hub to a 12mm thru-axle. Compatible with both Type 1 and Type 2 rear hubs.
$20.00 - $21.00
Front end cap conversion kits for NoTubes Neo and Neo Ultimate - SealLock end caps feature a low friction U-cup seal that snaps into place
$20.00 - $23.00
Rear end cap conversion kits for NoTubes Neo and Neo Ultimate hubs - SealLock end caps feature a low friction U-cup seal that snaps into place
$15.95 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
Compatible with straight valve hole Hugo 52 rims and designed to fit 7.5 - 8.5mm valve holes. Sold as a pair. Identifying your Hugo rim and selecting the correct valve stem: Stepped Hugo rims have a larger diameter valve hole on the interior of the rim, and a narrower hole on outside of the rim. Quick tip: don't remove your tire if you don't have to. If your Hugo rim decal reads: MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this valve. For "Stepped" valve hole Hugo use part AS0105 - Valve Stem pair, Schrader, 32mm, 14mm base.
Sta Tru Front Wheel - Measures 9-inch across, uses a 12-inch tire - Single Wall Rim - Hub/Brake Compatibility: Rim Brake - ISO Diameter: 203 / 12.5-inch - Front Axle: 5/16-inch x 85mm - Rim Width (Internal): 24 mm - Tire Type: Clincher
Sta Tru Rear Wheel - 104mm spacing - Includes 18 tooth rear cog - Single Wall rim - Hub/Brake Compatibility: Coaster Brake - Wheel Size: 12-inch - Cassette Body Type: 3 Prong Cog - ISO Diameter: 203 / 12.5-inch - Rim Width (Internal): 24 mm - Tire Type: Clincher - Rear Axle: 5/16-inch x 104mm
Sta-Tru Double Wall Front Wheels. - Hub/Brake Compatibility: Rim Brake - Wheel Size: 20-inch - ISO Diameter: 406 / 20-inch BMX - Front Axle: 3/8-inch x 100mm - Valve: Schrader - Tire Type: Clincher
Sta Tru Rear Wheels - Hub/Brake Compatibility: Rim Brake - Wheel Size: 700c - Cassette Body Type: Threaded Standard 1.37" x 24tpi - ISO Diameter: 622 / road / 29" - Tire Type: Clincher - Rear Axle: QR x 130mm
$74.99 - $85.00
Whether your joy comes from barreling downhill, or tearing up to the top, SRAM's MTH 716 front hub will leave a smile on your face. An aluminum hubshell with machined flanges grant the hub a low weight without compromising durability. TPlus, tough cartridge bearings roll smooth for the long haul.
3-pack, 298mm CX-Sprint Straight-Pull External Black Roam 60 29 Wheels
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
12x142mm conversion endcaps for Hope Pro 2 Evo rear hubs.
Hope Rear Axle Conversion Kits · For Pre-2011 Hope hubs labeled Pro2(axle and end caps)
- Longer skewers fit modern frames/forks with thicker dropouts - Aluminum lever/nut, Delrin pivot washer, serrated alloy nut with Nylock - White skewers are powder-coated - Shaft: chromoly - Wheel: front/rear - Spacing (front/rear): 100/135mm - Weight: 112g/set
$5.00 - $5.25
- Strong nylon reinforced PVC for a secure fit - Handles high-pressures; does not rot - 0.5mm thick
- Extra security against theft - 5mm hex CrMo axle
• Aluminum hub body with hollow steel axle • Fixed/Free • Sealed bearings • 120mm or 130mm rear spacing • 32 hole • 282 grams
This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum
Zipp Speed Weaponry Freehub Bodies - Material: Aluminum
Zipp Speed Weaponry Freehub Bodies - Material: Aluminum
The 202 Firecrest Carbon Clincher is a stiff, light weight and aerodynamic speed weapon ideal for every road. That's the power of Firecrest and Carbon Clincher technologies. The new 202 is the lightest entry in the Firecrest Carbon Clincher lineup, a do-it-all classic road wheel. This wheelset includes the 77/177 hubset. Firecrest rim technology affords the rider more speed, more stability, and more strength. This technology offers stable, predictable handling, and the wider rim increases lateral stiffness while offering greater vertical compliance Each Wheel Includes: - Zipp Tangente Quick Release Skewer - Zipp Tubeless valve – factory installed - Tubeless rim tape – factory installed - Valve core removal tool - Zipp 77D/177D thru-axle caps to fit 12x100, and 12x142 dropouts for rear wheels - Freehub body spacer – 11 to 10 speed - SRAM XDR driver body for 177D available separately
Upgrade your road bike with Zipp’s 30 Course Disc wheels. Featuring stiff, light 26mm-deep Zipp aluminum rims, Zipp's precision 77D/177D disc hubs and Sapim's outstanding CX-Ray spokes, these hoops maximize your power transfer for superior acceleration, climbing and handling. They also boast a 25mm-wide tire bed for running wider tires to improve the ride even more and minimize pinch flats.
Page 1 of 33 Next page